Steps to Create a Unicorn Horn Flower Crown

Due to the fact that who should have to choose between a flower crown and a unicorn horn? Kaia truly wished to wear both for her Birthday, and this is exactly what I wound up with.

When she initially told me she wished to be a unicorn for her Birthday party, I began poking around the Web, aiming to figure something out. I was truly disappointed with what I found. I didn't desire her to be encumbered by a huge, hot, bulky outfit for her indoor celebration. I wanted something she might don on her own when she desired to play. I didn't desire a modeling clay horn hung on with an "unnoticeable" flexible band. These just do not seem practical to me for a young kid. I wanted a horn that would go on quickly and comfortably, one that was light-weight, was not vulnerable, and would remain in location well on her head while she cantered around your home hugely, rearing and leaping. When you position a unicorn horn on a 4 year old, since you understand that is what is going to occur. (Omygosh, she's nearly four!) I believe I actually accomplished all these requirements I set myself, and I am truly pleased with how the entire thing came together, (therefore is she!).

When I made the horn, I was thinking I would experiment a bit, begin figuring things out. I didn't expect to be delighted with the very first thing I twiddled with, so I'm stuck without any images. I made a paper model in order to do this tutorial. Not the most beautiful photos, but ideally they at least make the procedure easy to see.

You will need:.

Craft Felt in Numerous Colours.
Stuffing.
Sewing Thread and Needle.
Extra Strong Quilting Thread.
Little Length of Elastic.
Headband.
Hot glue.
Scissors.
Plastic Gems.
Fabric Leaves (Or Make Felt Leaves).

I utilized sparkly white craft felt for her horn. Aside from the reality that it is, undoubtedly, sparkly, the sparkle felt is a fair bit stiffer. Cut out a slim triangle and fold it in half lengthwise, ideal sides together. Finish the open long side, marked with sharpy in the following pictures. Leave the bottom open. (That triangle was expected to be relatively in proportion. The real thing was, I swear. Pretend that it is fairly symmetrical, fine? Thanks.).

Cut off excess material, and turn right-side-out. Using additional strong quilting thread, cut a long piece, (enough to wrap your spirals,) and knot off completion. Make it a good, huge knot, you don't desire it to pull through the felt once there is stress on it. Run the thread out near the tip of the horn from within. (Not at the tip.) Pull everything the method through, so that knot is the only part left inside. Things the horn as securely as you can, I used polyfill stuffing. If needed, trim the bottom to even it out.

Start covering the thread down the horn in a spiral, tightly enough to leave an excellent indent. Tie your thread off inside, near the bottom of the horn. Put your horn on another piece of matching felt, trace the bottom circle, and cut it out.

Beginning with the within, cover stitches around the edges of your felt, sewing the circle to the bottom of the horn, and tie it off. Attempt to hide your knot inside, or a minimum of far from the edge.

I attached it to a good, large, cloth-covered headband that we found at a dollar store. To do so, determine a piece of flexible around the center of the headband to get your length, then make it Read Full Report a bit smaller sized so that it will extend snugly into place. Stitch the flexible ends together to form a loop. Stitch the flexible to the bottom of the horn. Make sure to stitch the elastic all the method to the edges of the horn, or the base will bring up at the front and back. Make sure that the seam holding the flexible together gets stitched to the horn, this method it will end up on top of the headband, instead of as an uncomfortable lump against your kid's head.

Your unicorn horn is complete! Like magic, the paper horn all of a sudden changes into a genuine one! Oh, wait ... * ehem * Anyway, once on the headband, I added a little hot glue under the edges of the horn to assist keep it from wobbling any. I think this would be fixed by using a larger flexible band than exactly what I took place to have on hand.

Cut a variety of flowers out of the coloured felt. I've no concept how well hot glue works on wool felt, however it works surprisingly on eco felt. For the big yellow flower, I merely cut a lot of strips of felt, folded them in half, then tacked them all together by their ends with a little thread.

Hot glue the flowers all over the headband, then hot glue the plastic gems to the centers. Ensure to overlap the base of the horn a bit and cover the rubber band. You are the happy brand-new owner of a unicorn horn flower crown!

I had a really tough time keeping her still long enough to take any images ...

Her rainbow unicorn tail is now complete, total, and I have a have actually blown complete galloping around the house all home. According to Kaia, nevertheless, she currently has 2 ears and didn't desire any more.

Because you know that is what is going to happen when you place a unicorn horn on a 4 year old. When I made the horn, I was thinking I would experiment a bit, start figuring things out. Make sure that the seam holding the elastic together gets sewn to the horn, this way it will end up on top of the headband, instead of as an uncomfortable lump against your child's head.

Make sure to overlap the base of the horn a bit and cover up the elastic band. You are the proud new owner of a unicorn horn flower crown!